VAG COM Fault Codes 17

4D27 P3295 19751 Linear Lambda probe 4 number / total weight of the cable: open circuit

4D28 P3296 19752 Linear Lambda probe 4 number / total weight of the cable: a short to ground

4D29 P3297 19753 Linear Lambda probe 4 number / total weight of the cable: short to positive

19754 4D2A P3298 catalyst system, Row 3: too low efficiency

19755 4D2B P3299 catalyst system, number 4: Too low efficiency

19756 4D2C P3300 Series 1, position sensor for exhaust camshaft => - G300: short to ground

4D2D P3301 19757 Bank 1, position sensor for exhaust camshaft => - G300: open circuit / short to positive

19758 4D2E P3302 Series 2, position sensor for exhaust camshaft => - G301: short to ground

19759 4D2F P3303 Series 2, position sensor for exhaust camshaft => - G301: open circuit / short to positive

19760 4D30 P3304 Series 1, a position sensor for exhaust camshaft-G300 / position sensor-G28 Crankshaft: mismatch signals

19761 4D31 P3305 Series 2, a position sensor for exhaust camshaft-G301 / position sensor-G28 Crankshaft: mismatch signalov19762

19762 4D32 P3306 Management ignition cylinder. 13: short circuit to ground

19763 4D33 P3307 Management ignition cylinder. 13: short circuit to plus

19764 4D34 P3308 Management ignition cylinder. 13: open circuit

19765 4D35 P3309 Management ignition cylinder. 14: short circuit to ground

19766 4D36 P3310 Management ignition cylinder. 14: short circuit to plus

19767 4D37 P3311 Management ignition cylinder. 14: open circuit

19768 4D38 P3312 Management ignition cylinder. 15: short circuit to ground

19769 4D39 P3313 Management ignition cylinder. 15: short circuit to plus

19770 4D3A P3314 ignition control, cyl. 15: open circuit

19771 4D3B P3315 Management ignition cylinder. 16: short circuit to ground

19772 4D3C P3316 ignition control, cyl. 16: short circuit to plus

19773 4D3D P3317 Management ignition cylinder. 16: open circuit

19774 4D3E P3318 Relay 2 switching glow-J495: short to positive

19775 4D3F P3319 Relay 2 switching glow-J495: open circuit / short to earth

19776 4D40 P3320 control signal supply 2 valves on the pump-injector: short to positive

19777 4D41 P3321 control signal supply 2 valves on the pump-injector: a failure in the electrical circuit

19778 4D42 P3322 Relay 2 Power terminals 30-J689: implausible signal

19779 4D43 P3323 Power kl.15 too high voltage level

19780 4D44 P3324 Power kl.15: open circuit

19781 4D45 P3325 Power kl.15: unreliable data

19782 4D46 P3326 switching flap valve intake manifold 2-N239: short to positive

4D47 P3327 19783 Intake manifold flap changeover valve 2-N239: open circuit / short to earth

19784 4D48 P3328 Motor damper intake manifold 2-V275: short to positive

19785 4D49 P3329 Motor damper intake manifold 2-V275: open circuit / short to earth

19786 4D4A P3330 Motor damper intake manifold 2-V275: no signal

19787 4D4B P3331 Motor damper intake manifold 2-V275: faulty

19788 4D4C P3332 recognition of the combustion process in the cylinders on the overrun.

4D4D P3333 19789 Control unit for turbocharger 1: unreliable message

19790 4D4E P3334 turbocharger control unit 2: unreliable message

4D4F P3335 19791 Control unit for turbocharger 1: There are no posts

19792 4D50 P3336 turbocharger control unit 2: There are no posts

4D51 P3337 19793 Data bus drive / motor: unreliable message

19794 4D52 P3338 supply control signal to the glow plug control 1: failure in the electrical circuit

19795 4D53 P3339 supply control signal to a control unit candle bulbs 2: failure in the electrical circuit

19796 4D54 P3340 Cooling Fan Relay charge air-J712: short to positive

19797 4D55 P3341 Cooling Fan Relay charge air-J712: short to ground

19798 4D56 P3342 Cooling Fan Relay charge air-J712: open circuit

19799 4D57 P3343 turbocharger control unit 1-J724: temperature too high

19800 4D58 P3344 turbocharger control unit 1-J724: supply voltage is out of range

19801 4D59 P3345 turbocharger control unit 2-J725: temperature too high

19802 4D5A P3346 turbocharger control unit 2-J725: supply voltage is out of range

19803 4D5B P3347 relay of inclusion glow: a failure in the electrical circuit

19804 4D5C P3348 supply control signal to the control unit of the turbocharger 1-J724: a failure in the electrical circuit

19805 4D5D P3349 supply control signal to the turbocharger control unit 2-J725: a failure in the electrical circuit

19806 4D5E P3350 Adapt gas mixture: out of range 1 (less than the minimum)

19807 4D5F P3351 Adapt gas mixture: out of range 1 (greater than the maximum)

19808 4D60 P3352 Adapt gas mixture: out of range 2 (less than the minimum)

19809 4D61 P3353 Adapt gas mixture: out of range 2 (greater than the maximum)

19810 4D62 P3354 Adapt gas mixture: out of range 3 (less than the minimum)

19811 4D63 P3355 Adapt gas mixture: out of range 3 (greater than the maximum)

19812 4D64 P3356 car catalyst system, gas-fired, number 1 too low efficiency

19813 4D65 P3357 lambda probe correction when working on gas: regulation limit reached

19814 4D66 P3358 probe 1, number 1, work on gas: the reaction time is too long

4D67 P3359 19815 Bank 1 Sensor 1, work on gas: the feedback heating circuit

4D68 P3360 19816 Bank 1 Sensor 1, work on gas: No Activity

19817 4D69 P3361 Work on gas: Misfire detected

19818 4D6A P3362 Work on the gas cylinder. 1: Misfire detected

19819 4D6B P3363 Work on the gas cylinder. 2: Misfire detected

19820 4D6C P3364 Work on the gas cylinder. 3: Misfire detected

19821 4D6D P3365 Work on the gas cylinder. 4: Misfire detected

19822 4D6E P3366 too high gas pressure in the system

19823 4D6F P3367 Too low gas pressure in the system

4D70 P3368 19824 Lambda Sensor 1 number 3: the signal is too lean

4D71 P3369 19825 Lambda Sensor 1 number 3: the signal is too rich mixture

4D72 P3370 19826 Lambda Sensor 1 number 4: the signal is too lean

4D73 P3371 19827 Lambda Sensor 1 number 4: the signal is too rich mixture

19828 4D74 P3372 switching flap valve Intake manifold geometry changes: short to ground

19829 4D75 P3373 switching flap valve changes the intake manifold geometry: open circuit / short to earth

19830 4D76 P3374 switching flap valve changes the intake manifold geometry 2: Short to Plus

19831 4D77 P3375 switching flap valve changes the intake manifold geometry 2: open circuit / short to earth

19832 4D78 P3376 air temperature sensor at the inlet 3-G520: signal too low

19833 4D79 P3377 air temperature sensor at the inlet 3-G520: signal too high

19835 4D7B P3379 high pressure valve for gas-N372: open circuit

19836 4D7C P3380 high pressure valve for gas-N372: short to positive

19837 4D7D P3381 high pressure valve for gas-N372: short to ground

19838 4D7E P3382 high pressure gas loop sensor-G400: open circuit

19839 4D7F P3383 sensor circuit high pressure gas-G400: short to positive

19840 4D80 P3384 sensor circuit high pressure gas-G400: short to ground

19841 4D81 P3385 sensor circuit low-pressure gas-G401: open circuit

19842 4D82 P3386 Sensor low pressure circuit gas-G401: short to positive

19843 4D83 P3387 Sensor low pressure circuit gas-G401: short to ground

19844 4D84 P3388 gas supply valve 1-N366: open circuit

19845 4D85 P3389 gas supply valve 1-N366: short to positive

19846 4D86 P3390 gas supply valve 1-N366: short to ground

19847 4D87 P3391 gas supply valve 2-N367: open circuit

19848 4D88 P3392 gas supply valve 2-N367: short to positive

19849 4D89 P3393 gas supply valve 2-N367: short to ground

19850 4D8A P3394 gas supply valve 3-N368: open circuit

19851 4D8B P3395 gas supply valve 3-N368: short to positive

19852 4D8C P3396 gas supply valve 3-N368: short to ground

19853 4D8D P3397 gas supply valve 4-N369: open circuit

19854 4D8E P3398 gas supply valve 4-N369: short to positive

19855 4D8F P3399 gas supply valve 4-N369: short to ground

28673 7001 U0001 damaged data bus drive

28700 701C U0028 Communication bus data drive

28772 7064 U0100 engine control unit: no connection

28773 7065 U0101 gearbox control unit: no connection

28775 7067 U0103 selector lever: no connection

28776 7068 U0104 Cruise control: there is no connection

28783 Block 706F U0111 energy management control: there is no connection

28787 7073 U0115 engine control unit: no connection

28793 7079 U0121 ABS control unit: no connection

28795 707B U0123 sensor rotation speed around the vertical axis: there is no connection

28798 707E U0126 sensor steering angle: there is no connection

28800 7080 U0128 control unit for electromechanical parking brake: no connection

28818 Block 7092 U0146 data bus diagnostic interface control: there is no connection

28823 7097 U0151 Unit airbag control: there is no connection

28827 709B U0155 unit dash panel: no communication

28836 70A4 U0164 control unit air conditioner: no connection

28907 70EB U0235 Adaptive cruise control: there is no connection

28974 712E U0302 gearbox control unit: incompatible software

28987 713B U0315 ABS control unit: incompatible software

28989 713D U0317 control unit for electromechanical parking brake: incompatible software

28993 7141 U0321 System leveling: incorrect software version

29076 7194 U0404 selector lever: implausible signal

29077 7195 U0405 Cruise control: implausible signal

29087 719F U0415 ABS control unit: implausible signal

29089 71A1 U0417 control unit for electromechanical parking brake: unreliable message

29093 71A5 U0421 System leveling: implausible signal

29696 7400 U1000 central control unit comfort systems-J393: no connection

29697 7401 U1001 central control unit comfort systems-J393: implausible signal

29698 7402 U1002 central control unit comfort systems-J393: Read data from the fault memory

29699 7403 U1003 recognition control unit-J345 Trailer: no connection

29700 7404 U1004 recognition control unit-J345 trailer: implausible signal

29701 7405 U1005 recognition control unit-J345 trailer: Read data from the fault memory

29702 7406 U1006 NOX sensor 1 Row 1: No connection

29703 7407 U1007 battery monitoring control unit: Read the data from the fault memory

29704 7408 U1008 Diagnostic interface data bus-J533: Read data from the fault memory

29705 7409 U1009 Diagnostic interface data bus-J533: unreliable message

29706 740A U1010 control unit for electromechanical parking brake: Read data from the fault memory

65280 FF00 development code 1

65281 FF01 development code 2

65282 FF02 development Code 3

65283 FF03 development code 4

65284 FF04 development code 5

65285 FF05 development code 6

65286 FF06 development code 7

65287 FF07 development code 8

65288 FF08 development 9 code

65289 FF09 development Code 10

65290 FF0A development Code 11

65291 FF0B development Code 12

65292 FF0C development code 13

65293 FF0D development Code 14

65294 FF0E development Code 15

65295 FF0F development Code 16

65296 FF10 development Code 17

65297 FF11 development Code 18

65298 FF12 development Code 19

65299 FF13 development Code 20

65300 FF14 development Code 21

65301 FF15 development Code 22

65302 FF16 development Code 23

65303 FF17 development Code 24

65304 FF18 development Code 25

65305 FF19 development Code 26

65,306 FF1A development Code 27

65307 FF1B development Code 28

65308 FF1C development Code 29

65309 FF1D development Code 30

65310 FF1E development Code 31

65311 FF1F development Code 32

65312 FF20 development Code 33

65313 FF21 development Code 34

65314 FF22 development Code 35

65315 FF23 development Code 36

65316 FF24 development Code 37

65317 FF25 development Code 38

65318 FF26 development Code 39

65319 FF27 development Code 40

65320 FF28 development Code 41

65321 FF29 development Code 42

65322 FF2A development Code 43

65323 FF2B development Code 44

65324 FF2C development Code 45

65325 FF2D development Code 46

65326 FF2E development Code 47

65327 FF2F development Code 48

65328 FF30 development Code 49

65329 FF31 development Code 50

FFFF 65535 Faulty control unit

Types of errors

 

001 01 signal to plus

Signal 002 to ground 02

003 03 no signal

004 04 mechanical damage

005 05 input open

06 006 is too high signal level

07 007 is too low signal level

08 008 out of the control range (greater than the upper limit)

09 009 out of the adaptation range (greater than the upper limit)

0A 010 out of the adaptation range (less than the lower limit)

011 0B way out of the control range (less than the lower limit)

012 0C out of the adaptation range, greater than the upper limit (under load)

0D 013 out of the adaptation of the range below the lower limit (under load)

014 0E output of adaptation range, greater than the upper limit (idling)

015 0F out of the adaptation range, below the lower limit (at idle)

016 10 Signal outside tolerance

017 11 adjustment range

12 018 upper limit

019 13 lower limit value

020 14 Basic installation error

021 15 front pressure increases too long

022 16 front pressure is reduced too long

023 17 rear pressure increases too long

024 18 rear pressure decreases too long

025 19 undefined switch state

026 1A output open

027 1B implausible signal

028 1C short to positive

029 1D short to ground

030 1E open circuit / short to positive

031 1F open circuit / short to earth

032 20 resistance value is too high

033 21 resistance value is too small

22 034 type of error is not defined

035 23

036 24 open circuit

25 037 defective

038 26 Output does not switch / short to positive

039 27 Output does not switch / short to ground

040 28 short to another valve

29 041 blocked, or there is no voltage

2A 042 is too large deviation speed

043 2B is closed

044 2C shorting

045 2D connector

046 2E depressurization

047 2F connected properly

048 30 Power Supply

049 31 no connection

050 32 no early position is reached

051 is not reached within 33 position

052 34 Supply voltage is too high

053 35 too low voltage

054 36 Equipment selected incorrectly

055 37 adaptation is not performed

38 056 in emergency mode

39 057 in an electrical circuit failure

058 3A is not locked

059 3B is unlocked

3C 060 is not included SAFE lock locks

061 3D is not disabled Lock SAFE locks

3E 062 settings are not performed or performed incorrectly

063 3F in temperature shutdown

43 067 is reached the nominal value

068 44 Cylinder 1

069 45 cylinder 2

070 46 cylinder 3

071 47 cylinder 4

072 48 cylinder 5

073 49 6 Cylinder

074 4A cylinder 7

075 4B cylinder 8

076 4C cells. 30 missing

077 4D internal supply voltage

078 4E lack of communication.

079 4F to read data from the fault memory

50 080 in one-wire mode

081 51 open

082 52 launched

C0 192 is currently checked

193 C1 does not have access

194 C2 correction is not performed